A person encounters all sorts of things in life, and so too in the sitar world. I knew that there are children’s sitars (mini sitar or baby sitar) that can also be played, but I had never seen such a gem before. What would you call it? A tiny toy sitar? But it seems more then only a toy designed to me, which you can then actually play on (if you want to). Calling it a “Tom Thumb sitar” sounds good, I guess…. 😉

Anyway, the little instrument did need some cleaning and repair work before anything could be done with it. The bridge was missing and a few tuning pegs were broken. Other than that, it wasn’t too bad. So, I made a new bridge out of a tarav bridge and found some old matching tarav kuntis.

Tom Thumb has 10 pardas, 5 taravs and possibly up to 7 main strings. The scale is only 36cms, the body is 55cms long and the tabli 14cms wide. The neck is only 5.4cms wide. The ‘tumba’ is probably all wood, with a good bit of plastering to get it nice and round. Otherwise complete with simple decoration on celluloid, just like its big brothers & sisters!

Tom Thumb sitar string set / tuning chart (example):

1. steel wire 0,28mm / N°2 tuned to A#4
2. bronze wire 0,37mm / N°28 tuned to C#3
3. bronze wire 0,46mm / N°26 tuned to G#3
4. steel wire 0,23mm / N°0  tuned to G#4
5. steel wire 0,19mm / N°000 tuned to C#5
6. steel wire 0,19mm / N°000 tuned to C#6
Taravs: steel wire 0,19mm / N°000

She has undergone a full restoration and is ready to please another sitar player. She is also very suitable for the committed beginner.

Now for sale on this site (click here).

Here then is a photo report of the work carried out:

More neck bend repair can be found here.

The jack connector will be built a bit further up the tumba to achieve more comfortable accessibility.

Because the tumba is rather thin and weak, I make a rounded wooden support that is glued firmly to the inside of the tumba. This way, the connection can take a bit of rough handling….

Then the two transducers are glued to the tabli on the inside. I provide a small piece of white cotton soaked in white wood glue to secure the wiring.
Once this assembly is successful, the various tumba parts are glued until the puzzle is complete. However, one small piece is missing. The hole is filled with a mixture of wood dust, plaster and wood glue.

This is followed by further finishing of the tumba with colour and the whole instrument is given another coat of finishing shellac polish.

The pardas are polished and re-tied, kuntis are cleaned and treated with chalk, new strings put on and jawari done… and there we go.

Read here an article about mounting K&K Big Twin internal external

Read here an article about mounting K&K Pure 12-String internal

This is the follow-up report to a project on the restoration of a special Hiren Roy sitar. Click here for the  first part. Below is the second part concerning the result:

The original second tumba is missing. This is very unfortunate for a sitar that is around 60 years old. It is easy to see from the photos that this is a fairly large second tumba. Not surprising for sitar of this class. I myself do not have any tumbas in stock, nor can I make them just like that. But for some time now, I have been working regularly with Mohammad Waseem Maner, a young and talented sitar maker from Miraj. I asked him if he could then make a replica of this missing second tumba for us. “Yes. Sir I will do the needful” was his prompt reply and so it happened.

The new second tumba arrived just in time to still be mounted on the fully repaired instrument. And, Waseem did a sterling job. The cut-outs in the woodwork match those of the original perfectly.

Following are some photos of the finished instrument.

Time to dwell for a moment on the unusual bridge on the head of the neck.

It is widely known that traditionally built sitars do easily suffer from anomalous intonation. This is especially noticeable with the Laraj Kharaj strings. Modern western instruments are often equipped with options to adjust the length of each string separately so that one can achieve quasi-perfect intonation. But that is not easy to achieve on a simple construction like a sitar.

Many sitar maestros started experimenting with an extra bridge added to the bridge at the head of the neck. The construction found on this instrument takes the crown. At first, only the length of the Laraj Kharaj string was adjusted. In principle, that should have sufficed, but apparently it could have been even better. An extra bridge was added later. This time, the Jora string was included in the adjustment.

The result is impressive, though. The intonation of this sitar is one of the cleanest I have ever heard. Once the new strings were fitted and the instrument was given a first tuning, it was noticeable that all the strings can be played quasi right on the fret. Very special, especially then with the Laraj Kharaj….

Only drawback Matyas quickly found was that the Kharaj, when played open, easily tended to go into an excessive buzz. This is not surprising given the actual width of this extra bridge on the headstock. The problem was remedied by turning in the accompanying screw a little deeper, though. But whether this will hold up in the longer term Matyas can tell us soon….
In any case, this sitar is ready for a new start with a promising young sitarist Matyas Wolter. And they lived happily ever after together…. 😉

Those who would like to hear this sitar in the hands of its master please visit Matyas playlist of Ustad Ilyas Khan’s music on his archival YouTube site:

Ustad ILYAS KHAN: https://www.youtube.com/playlist?list=PLvP9MFDf6jaLLvf-4xvUVTsIEkpm3hOsL

Those who would like to hear this restored sitar in the hands of Matyas himself listen here:

Matyas Wolter: https://www.youtube.com/watch?v=4SA9T4OYYrI

This unique Hiren Roy sitar now belongs to German sitarist Matyas Wolter. In spring 2023, he sent me for a list of problems:

A. Structural Issues:
> Open the tabli and neck plate and tighten all loose points
> If it is opened once anyways, maybe it could be tried to straighten the neck???!!!
B. Cosmetics:
> Spot repair of torn polish spot in front of lower bridge leg on the tabli
> Spot repair of gourd pimples
C. Setup:
> All obvious works: fret binding & setting, new strings etc
> Original Horn bridge adjustment, and (possibly after neck repair) heightening

Since this is a larger project, I have split the report into 2 parts. Below is the first part concerning basic repair:

The sitar almost fell apart by itself. It had once been glued with rohlam, a traditional wood glue made from a mixture of wheat flour, lime and copper sulphur. After a (long) time, it came apart easily.

So taking the instrument apart wasn’t too bad. The neck came off easily with a couple of scrapers inserted and almost immediately the whole tabli came off too.

Matyas had noted earlier that the tabli was probably loose, and that was no overstatement.
The joint on the other hand was still firmly attached, but once the 4 screws were loosened, it too came apart perfectly.

By special request from Matyas, I have put a message to the inside of the neck plate:

“This sitar was made by Hiren Roy of Calcutta in the early 1960’s for Ustad Ilyas Khan of Lucknow and was his main sitar until he passed away in 1989. Thereafter his son Idris Khan took care of it. After Idris’ demise in 2013 Ilyas Khan’s nephew Ustad Irfan Khan of Calcutta took over. He passed the instrument on to his German disciple Matyas Wolter in 2023. It was completely restored for a new life by Klaas Janssens at Sitarfactory / Belgium in 2023.”

The various parts were then well cleaned and cleared of rohlan residue. I then glued them back together with modern hide glue. First up was the neck as it was slightly warped. Then the tabli was put back on. Everything was fixed and held as per the traditional way, with rope…

After a few days of drying, the next step came: the tumba. Matyas had noticed strange bulges, gourd pimples, on the surface and now a little later I came to a peculiar discovery. There were screws under the surface. Due to the effect of rust, and probably also the metal expanding and contracting, slight bulges formed on them over time.

I had never experienced this construction before and still wonder about the purpose of these screws. I can only imagine that they served to help improve the natural shapes of the harvested pumpkin so that it could be made nice and round. The screws probably served to hold the various cuts firmly together again. This is no longer necessary with today’s modern wood glues, which make a good solid joint.

As you can see from the photos, quite a few adjustments were made. I then removed all the bulges, cleaned them well and then gave them a new coat of wood glue/wood dust mixture.

Finally, after this exceptional job, the finishing procedure follows: tumba colouring, body polishing, fitting frets and bridges and finally new strings on… Because the neck is now nicely straight again, the height of the strings changes and so the height of the bridge has to be adjusted as well.

A second report will come soon with more info and photos of the final result.

This sitar still has a mystery… click here for the second part.

Hallo,

I got the chance to buy an old Rikhi Ram GP Sitar for 40€ only (the 60yo sellers dad died and she kept it since~30yrs ago so I would guess 1970s or 80s).

The sitar looks very good and has the white/gold Rikhi Ram label, but the gourd is broken on two positions or more. Some parts of the gourd they kept, some parts are missing. Someone unfortunately already tried to repair it without any success, the repaired pieces look extremely shitty glued 😀
I would like to get the sitar repaired, but I wouldn’t trust me to do it so I thought Ill contact you as I follow your blog enthusiastically for some time now.

Can I maybe send you some pictures to get you an impression of the damage? Since the sitar just stood around for 30ish years, I would like to get a full facelift done of everything plus jawari of course.

Sören, from Germany

A while later, the sitar has arrived…
Terrible what happened to this sitar:

It is difficult to find out what product was used. I think it must have been a hard synthetic glue on the inside, and then overlaid by a hard hot glue on the outside.

The good news is that the construction on the inside is well done firmly, so that is a good point. I can remove the hard glue on the outside with a chisel and make it smooth again. The tumba is definitely repairable. It does have a few pieces missing, but I can repair them with pieces from another broken tumba I have lying around here.

Once the tumba is ready, I can remove the remnants of that shitty glue on the outside with sandpaper and smooth the surface. A new black wax bond is also applied.

Followed by a finish with new colour & shellac lacquer layers.

The rest of the sitar looks fine. All the pegs are ok but turn very stiffly, the frets are oxidised but of fine quality, a good bridge in horn is present and intact and the joint is tight.

Finally frets repolishing and binding, new strings, doing jawari and tuning etc…

I think this sitar is definitely worth all the work. It is a common good quality Rikhi Ram Gandhar Pancham 70-80’s model that has potential to be a good sounding & reliable sitar. So be it! 🙂

Technical info on strings & tuning according to Asad Ali Khan style:

The scale measures 945cm & the instrument is tuned to G#
Cikari’s: steel 0,30mm (N°3) tuned to G#3 (SA) & G#4 (SA)
Baj tar: steel 0,40mm (N°6) tuned to C#2 (MA)
SA tar: bronze 0,56mm (N°24) tuned to G#2 (SA)
PA tar: bronze 0,72mm (N°22) tuned to D#2 (PA)
Kharaj: flatwound bronze 0,92mm (N°20) tuned to G#1 (SA)
Laraj: bronze 0,56mm (N°24) tuned to G#2 (SA)

For more info about rudra veena you can visit www.rudravina.com and www.rudraveena.org

The scale measures 59cm only and the string set is:
1: 0,58mm brass RW string tuned to C3
2: 0,37mm bronze string tuned to F4
3: 0,37mm bronze string tuned to F4
4: 0,75mm brass RW string tuned to F3

Sound sample: Play PA-sa-sa-SA tanpura in F